background image

2

PARTS: 

HARDWARE KIT PART # 21737

WARNING:

 

Serious or fatal crushing injuries can occur from furniture tip-over.  To help prevent tip-over:

.

Place heaviest items in the lowest drawers.

.

Unless specifically designed to accommodate, 

do not

 set TV’s or other heavy objects on the top of this 

product.

.Never

 allow children to climb or hang on drawers, doors,or shelves.

.Never

 open more than one drawer at a time.

Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

.

Always monitor your child’s activity when in the nursery.

.Do not

 allow standing in drawers.

.Do not

 allow standing on top of this product.

.

Accessory Items must be securely fastened to this product according to the instructions provided with 

those items.

.

To avoid head injury, do not allow children to play underneath open drawers.

.

Do not leave drawers open when not in use.

NOTES ON ASSEMBLY:

-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on 

the diagram of the item which is drawn actual size and design. Be sure to use the proper size and 

shape specified in the instructions.

-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly 

recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON CARE AND MAINTENANCE:

Do not

 scratch or chip the finish.

- Inspect the product periodically, contact delta children's products for replacement parts or questions.

Do not

 store the product or any parts in extreme temperatures and conditions such as a hot attic or a 

damp, cold basement. These extremes can cause a loss of structural integrity.

-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or 

felt pad under any items you place on the finish.

-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.  

-

Do not

 use abrasive chemicals.  

-

Do not

 spray cleaners directly onto furniture.

-Lift slightly when moving on carpeting to prevent leg breakage.

-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

KK. 30mm Wood 

Dowel x46

LL. Plastic 

Barrel Nut x24

MM. Plastic Crescent 

Washer X 8

PP. Knob x6

Part# 21739

M5 BALL HEX 

ALLEN WRENCH

M4 BALL HEX 

ALLEN WRENCH

PHILLIPS 

SCREWDRIVER

AA. 75mm Bolt x1

BB. 65mm Bolt x8

CC. 55mm Bolt x1

DD. 45mm Bolt x10

EE. 35mm Bolt x4

FF.  40mm Screw x24

GG. 30mm Screw x14

NN. 25mm Screw x30

HH. 15mm Back 

Panel Screw x20

JJ. 25mm Knob 

Screw x6

Summary of Contents for 75106 Series











Reviews: