DèLonghi ESAM6620, Manual

Page: 20 / 222

19
Su
performs a series of rinses and pauses to
remove limescale deposits from inside the
machine.
After about 30 minutes, the message “RINSING...
FILL TANK!” is displayed.
9. The appliance is now ready for rinsing
through with clean water.
Remove the water tank, empty, rinse
under running water, fill with clean water
and replace. “RINSING... PRESS OK” is
displayed.
10. Empty the container used to collect the
descaler solution and replace it under the hot
water spout.
11. Press the OK button to start rinsing. Hot
water flows out of the spout and the message
“RINSING...” is displayed.
12. When the water tank is completely empty,
the message “RINSING COMPLETE... PRESS
OK” is displayed.
13. Press the OK button, fill the water tank and
the appliance is ready for use.
SETTING WATER HARDNESS
The DESCALE message is displayed after a
period of time established according to water
hardness.
The machine is factory set for a hardness value
of 4. The machine can also be programmed
according to the hardness of the mains water in
the various regions, varying the frequency with
which the message is displayed.
Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST”
indicator paper from its pack.
2. Immerse the paper completely in a glass of
water for one second.
3. After about a minute, 1, 2, 3, or 4 red squares
form, depending on the hardness of the water.
Each square corresponds to one level.
Level 1
Level 2
Level 3
Level 4
Set water hardness
1. Press the P button to enter the menu.
2. Press the button (corresponding to
the symbol flashing on the display)
repeatedly until the menu arrow is on
“WATER HARDNESS”.
3. Confirm the selection by pressing the OK
button.
4. Press the button (corresponding to the
SET symbol flashing on the display) until the
number displayed coincides with the number
of red squares on the test strip.
5. Press the OK button to confirm the setting.
6. Press the P button (corresponding to the
ESC symbol flashing on the display) to exit
programming mode or to change other
parameters.
The machine is now reprogrammed with the new
water hardness setting.
SETTING THE LANGUAGE
To change the language on the display, proceed
as follows:
UÊ *ÀiÃÃÊ Ì iÊ OK button for at least 5 seconds
until the appliance displays the installation
message in various languages.
UÊ 7 i˜ÊÌ iʏ>˜}Õ>}iÊÀiµÕˆÀi`Ê>««i>ÀÃ]Ê«ÀiÃÃÊ
OK for 3 seconds.
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350W
Pressure: 15 bars
Water tank capacity: 1,8 litres
Size LxHxD: 282x374x441 mm
Weight: 11,4 Kg
The appliance complies with the following EC
directives:
UÊ “Low voltage Directive” 2006/95/CE and
suc¬cessive amendments.
UÊ ºÊ ˆÀiV̈Ûi»Ê Ê EMC 2004/108/CE and
successive amendments.
UÊ / iÊ “>ÌiÀˆ>ÃÊ >˜`Ê œLiVÌÃÊ `iÃ̈˜i`Ê ÌœÊ
come into contact with food stuffs are
in compliance with the provisions of the
1935/2004 European Standard.