122
• At the end of delivery, to increase the quantity of coffee in
the cup, just press (within 3 seconds) one of the coffee but-
tons (
or
) (fig. 17).
Once the coffee has been made, the appliance is ready to make
the next drink.
Please note!
• Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in section “18. Displayed
messages”.
• For hotter coffee, see section “9.5 Tips for a hotter coffee”.
• If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in section “19.
Troubleshooting”.
9.7 Making coffee using pre-ground coffee
Important!
• Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
• Never use more than 1 level measure (C2) or it could dirty
the inside of the coffee machine or block the funnel (A4).
Please note!
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
1. Press the
button (B2-fig. 11) until “Pre-ground”
appears on the display (B13).
2. Open the pre-ground coffee funnel lid (A2).
3. Make sure the funnel (A4) is not blocked, then add one
level measure of pre-ground coffee (fig. 18).
4. Place a cup under the coffee spouts.
5. Press the 1 cup coffee button
(B11).
6. Preparation begins. The amount of coffee selected is dis-
played together with a progress bar which gradually fills as
preparation progresses.
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before the first coffee is delivered.
9.8 Making LONG coffee using coffee beans
Prepare the appliance following the instructions in the section
“9.6 Making coffee using coffee beans”, then press the
button (B9-fig. 19): “LONG COFFEE FUNCTION” appears on the
display (B13), together with a progress bar which fills gradually
as preparation proceeds.
9.9 Making LONG coffee using pre-ground coffee
Follow the instructions in points 1, 2, 3 and 4 of the section
“Making coffee using pre-ground coffee”, then press the
button (B9- fig. 19).
The appliance starts making coffee and “LONG COFFEE FUNC-
TION” appears on the display (B13), together with a progress bar
which fills gradually as preparation proceeds. Halfway through
preparation, the message “ADD PRE-GROUND COFFEE, Press OK”
appears. Add one level measure of pre-ground coffee and press
OK
(B12-fig. 10).
Preparation resumes and the appliance displays a progress bar
which fills gradually as preparation proceeds.
9.10 Customising the LONG coffee quantity
The appliance is set by default to automatically deliver about
180ml of LONG coffee. To modify these settings, proceed as
follows:
1. Place a sufficiently large cup or glass under the coffee
spouts (A7- fig. 13).
2. Press and hold the
button (B9-fig.19) until “Pro-
gram quantity” is displayed.
3. Press the
button. The appliance starts delivering
coffee;
4. As soon as the coffee in the cup reaches the required level,
press the
button again.
The quantity of coffee in the cup has now been programmed.
Please note!
If the programme uses pre-ground coffee, the appliance will
prompt you to add a second level measure of coffee.
10. MAKING CAPPUCCINOS AND MILK-BASED
COFFEES
Please note!
• To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid (D2) and hot water con-
nection nozzle (A8) as described in sections “10.5 Cleaning
the milk container after every use”, “12.10 Cleaning the
milk container” and “12.11 Cleaning the hot water/steam
connection nozzle”.
10.1 Filling and attaching the milk container
1. Remove the lid (D2- fig. 20);
2. Fill the milk container (D3) with a sufficient quantity of
milk, not exceeding the MAX level marked on the contain-
er (fig. 21). Each mark on the side of the container corre-
sponds to about 100 ml of milk.
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If “Energy Saving” mode is enabled, you may have to wait a
few seconds before the drink is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (fig. 22).
4. Place the lid back on the milk container.
5. Extract the hot water spout (C6) by pressing the button
(C7) on the spout (fig. 23A and B).
6. Attach the milk container to the connection nozzle (A8)
and push as far as it will go (fig. 24). The machine emits a
beep (if the beep function is enabled).
7. Place a sufficiently large cup under the coffee spouts (A7)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fig. 25).
8. Follow the instructions below for each function.
10.2 Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coffees.
Dial
position
Description
Recommended for…
No froth
CAFFELATTE /
MILK (hot milk)
Min. froth
LATTE MACCHIATO/
FLAT WHITE
Max. froth
CAPPUCCINO /
MILK (frothed milk)/ ESPRES-
SO MACCHIATO
10.3 Making cappuccinos and milk-based coffees
automatically
The CAPPUCCINO (B3), CAFFELATTE (B4) and LATTE MACCHIATO
(B5) buttons on the control panel (B) enable these drinks to be
prepared automatically. Proceed as follows:
1. Fill the milk container (D) and attach it as described above.
2. Turn the froth adjustment dial (D1) on the milk container
lid (D2) to the position corresponding to the required froth.
3. Press the button corresponding to the required drink.
The name of the drink selected is displayed together
with a progress bar which gradually fills as preparation
progresses.
