131
3. Press < (B4) or > (B8-fig. 9) until “Install filter, Enabled” is
displayed;
4. Press the
OK
button (B12- fig. 10);
5. “Disable?” appears on the display;
6. Press the
OK
button to confirm and the
MENU/ESC
button
to exit the menu.
16. TECHNICAL DATA
Voltage:
220-240 V~ 50/60 Hz max. 10 A
Power:
1450 W
Pressure:
1,5 MPa (15 bar)
Water tank capacity:
2 L
Size LxDxH:
260x470x365 mm
Cord length:
1750 mm
Weight:
11 kg
Beans container capacity:
400 g
The appliance complies with the following EC
directives:
• European Standby Regulation 1275/2008
• Materials and accessories coming into contact with food
conform to EEC regulation 1935/2004.
17. DISPOSAL
The appliance must not be disposed of with house-
hold waste, but taken to an authorised waste separa-
tion and recycling centre
18. DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
FILL TANK
Insufficient water in the tank (A16).
Fill the tank with water and/or insert it cor-
rectly, pushing it as far as it will go until it
clicks into place.
EMPTY GROUNDS CONTAINER The grounds container (A10) is full.
Empty the grounds container and drip tray
(A12), clean and replace (fig. 31). Important:
when removing the drip tray, the grounds
container (A10) MUST be emptied, even if it
contains few grounds. If this is not done, when
you make the next coffees, the grounds contai-
ner may fill up more than expected and clog the
machine. If the problem persists, make sure the
water tank (A16) is fully inserted, press the
button (B7) and deliver a little water from the
spout (C6).
GROUND TOO FINE ADJUST
MILL
The grinding is too fine and the coffee is delive-
red too slowly or not at all.
Repeat coffee delivery and turn the grin-
ding adjustment dial (A5, fig. 14) one click
clockwise towards “7” while the coffee mill is
in operation. If after making at least 2 coffees
delivery is still too slow, repeat the correction
procedure, turning the grinding adjustment
dial another click (section “9.5 Adjusting the
coffee mill”).
If the water softener filter (C4) is present, an
air bubble may have been released inside the
circuit, obstructing delivery.
Insert the hot water spout (C6) in the appliance
and deliver a little water until the flow beco-
mes regular.
INSERT GROUNDS CONTAINER After cleaning, the grounds container has not
been replaced (A10).
Remove the drip tray (A12) and insert the
grounds container.
ADD PRE-GROUND COFFEE
With the “pre-ground coffee” function selected,
pre-ground coffee has not been poured into the
funnel (A4).
Place pre-ground coffee in the funnel or dese-
lect the “pre-ground” function (fig. 18).
DESCALE
The machine must be descaled.
The descaling procedure described in section
“13. Descaling” needs to be performed as soon
as possible.
REDUCE COFFEE AMOUNT
Too much coffee has been used.
Select a milder taste by pressing the
button (B2- fig. 11) or reduce the quantity of
pre-ground coffee.
FILL BEANS CONTAINER
The coffee beans have run out.
Fill the beans container (fig. 15).
The pre-ground coffee funnel (A4) is clogged.
Empty the funnel with the help of the brush
(C5) as described in section “12.8 Cleaning the
pre-ground coffee funnel”.
INSERT INFUSER ASSEMBLY
The infuser has not been replaced after clea-
ning (A15).
Insert the infuser as described in section “12.9
Cleaning the infuser”.
INSERT TANK
The tank (A6) is not correctly in place.
Insert the tank correctly and press as far as it
will go.
GENERAL ALARM
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly,
as described in section “12. Cleaning”. If the
message is still displayed after cleaning, con-
tact a service centre.
EMPTY CIRCUIT FILL CIRCUIT
alternating with
HOT WATER
Press OK
The water circuit is empty
Press OK (B12- fig. 10) to deliver water from
the spout (C6) until it flows out normally. If the
problem persists, make sure the water tank
(A16) is fully inserted.
REPLACE FILTER
The water softener filter (C4) is exhausted.
Replace the filter or remove it as described in
section “15. Water softener filter”
SET DIAL TO CLEAN
Milk has been delivered recently and the tubes
inside the milk container must be cleaned (D).
Turn the froth adjustment dial (D1) to the
CLEAN position.
INSERT WATER SPOUT
The hot water spout (C6) is not inserted or is
inserted incorrectly
Insert water spout as far as it will go.
