123
9.9 Making LONG coffee using pre-ground coffee
Follow the instructions in points 1, 2, 3 and 4 of the section
“Making coffee using pre-ground coffee”, then press the
button (B9- fig. 19).
The appliance starts making coffee and “LONG COFFEE FUNC-
TION” appears on the display (B13), together with a progress bar
which fills gradually as preparation proceeds. Halfway through
preparation, the message “ADD PRE-GROUND COFFEE, Press OK”
appears. Add one level measure of pre-ground coffee and press
OK
(B12-fig. 10).
Preparation resumes and the appliance displays a progress bar
which fills gradually as preparation proceeds.
9.10 Customising the LONG coffee quantity
The appliance is set by default to automatically deliver about
180ml of LONG coffee. To modify these settings, proceed as
follows:
1. Place a sufficiently large cup or glass under the coffee
spouts (A7- fig. 13).
2. Press and hold the
button (B9-fig.19) until “Pro-
gram quantity” is displayed.
3. Press the
button. The appliance starts delivering
coffee;
4. As soon as the coffee in the cup reaches the required level,
press the
button again.
The quantity of coffee in the cup has now been programmed.
Please note!
If the programme uses pre-ground coffee, the appliance will
prompt you to add a second level measure of coffee.
10. MAKING CAPPUCCINOS AND MILK-BASED
COFFEES
Please note!
• To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid (D2) and hot water con-
nection nozzle (A8) as described in sections “10.5 Cleaning
the milk container after every use”, “12.10 Cleaning the
milk container” and “12.11 Cleaning the hot water/steam
connection nozzle”.
10.1 Filling and attaching the milk container
1. Remove the lid (D2- fig. 20);
2. Fill the milk container (D3) with a sufficient quantity of
milk, not exceeding the MAX level marked on the contain-
er (fig. 21). Each mark on the side of the container corre-
sponds to about 100 ml of milk.
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If “Energy Saving” mode is enabled, you may have to wait a
few seconds before the drink is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (fig. 22).
4. Place the lid back on the milk container.
5. Extract the hot water spout (C6) by pressing the button
(C7) on the spout (fig. 23A and B).
6. Attach the milk container to the connection nozzle (A8)
and push as far as it will go (fig. 24). The machine emits a
beep (if the beep function is enabled).
7. Place a sufficiently large cup under the coffee spouts (A7)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fig. 25).
8. Follow the instructions below for each function.
10.2 Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coffees.
Dial
position
Description
Recommended for…
No froth
CAFFELATTE /
MILK (hot milk)
Min. froth
LATTE MACCHIATO/
FLAT WHITE
Max. froth
CAPPUCCINO /
MILK (frothed milk)/ ESPRES-
SO MACCHIATO
10.3 Making cappuccinos and milk-based coffees
automatically
The CAPPUCCINO (B3), CAFFELATTE (B4) and LATTE MACCHIATO
(B5) buttons on the control panel (B) enable these drinks to be
prepared automatically. Proceed as follows:
1. Fill the milk container (D) and attach it as described above.
2. Turn the froth adjustment dial (D1) on the milk container
lid (D2) to the position corresponding to the required froth.
3. Press the button corresponding to the required drink.
The name of the drink selected is displayed together
with a progress bar which gradually fills as preparation
progresses.
4. After a few seconds, frothed milk is delivered from the milk
spout (D5) into the cup below. Then the machine automat-
ically makes the coffee after delivering the milk.
10.4 Preparing “MILK MENU” drinks
Besides the drinks described above, the appliance automatical-
ly prepares MILK (lhot milk), FLAT WHITE, MACCHIATO and MY
MILK (customisable).
To prepare one of these drinks, simply proceed as follows:
1. Fill the milk container (D) and attach it as described above
(fig. 24).
2. Turn the froth adjustment dial (D1) on the milk container
lid (D2) to the position corresponding to the required froth.
3. Press the MILK MENU button (B6).
4. Press < (B4) or > (B8) until the drink to be programmed
appears on the display (B13) (MILK, FLAT WHITE, ESPRESSO
MACCHIATO or MY MILK).
5. Press the
OK
button (B12- fig. 10) to start delivery.
6. After a few seconds, frothed milk is delivered from the milk
spout (D5) into the cup below. For drinks with coffee, the
machine automatically makes the coffee after delivering
the milk.
Please note: general indications when preparing all
milk-based drinks
• If you want to interrupt preparation during delivery, press
the corresponding button.
• At the end of delivery, to increase the quantity of milk or
coffee in the cup, just press and hold (within 3 seconds) the
button corresponding to the drink being made.
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
10.5 Cleaning the milk container after every use
Important! Danger of burns
When cleaning the internal tubes of the milk container (D), a lit-
tle hot water and steam leak out of the frothed milk spout (D5).
Avoid contact with splashes of water.
“SET DIAL TO CLEAN” flashes on the display (B13) each time you
use a milk function. To eliminate all milk residues, proceed as
follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk spout.
3. Turn the froth adjustment dial (D1) to “CLEAN” (fig. 26). A
progress bar appears and gradually fills as the operation
proceeds together with “Cleaning underway”. Cleaning
stops automatically.
