16
Cleaning the milk container” and “15.11 Cleaning the hot water/
steam connection nozzle”.
10.1 Filling and attaching the milk container
1. Remove the lid (D2) (fig. 14);
2. Fill the milk container (D3) with a sufficient quantity of milk,
not exceeding the MAX level marked on the container (fig.
15). Each mark on the side of the container corresponds to
about 100 ml of milk;
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If "Energy Saving" mode is enabled, you may have to wait
a few seconds before the beverage is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (fig. 16);
4. Place the lid back on the milk container;
5. If present, extract the hot water/steam spout (C6) by press-
ing the release button (C7) (fig. 17);
6. Attach the milk container (D) to the connection nozzle (A9)
(fig. 18) and push as far as it will go. The machine emits a
beep (if the beep function is enabled);
7. Place a sufficiently large cup under the coffee spouts (A8)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fig. 19).
8. Follow the instructions below for each function.
10.2
Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coffees.
Dial
position
Description
Recommended for…
NO FROTH
HOT MILK (not frothed) /
CAFFELATTE
MIN. FROTH LATTE MACCHIATO /
FLAT WHITE
MAX. FROTH CAPPUCCINO / CAPPUCCI-
NO+ / CAPPUCCINO MIX
/ ESPRESSO MACCHIATO /
HOT MILK (frothed)
10.3
Making cappuccino and milk-based
coffees automatically
1. Fill the milk container (D) and attach it as described above.
2. Select the required beverage:
Directly selected beverages:
• CAPPUCCINO (B10)
• LATTE (B11)
• FLAT WHITE (B12)
• HOT MILK (B13)
Selectable from the beverages selection menu (B3):
• CAP
• ESPRESSO MACCHIATO
• CAFFELATTE
• CAPPUCCINO MIX
3. A message on the display (B1) instructs you to turn the
froth adjustment dial (D1) according to the froth required
by the original recipe. Turn the dial on the milk container
lid (D2) and confirm the selection by pressing the selection
arrow (B2) corresponding to " OK".
4. After a few seconds, preparation begins automatically and
an image of the selected beverage appears on the display,
together with a progress bar which gradually fills as prepa-
ration progresses.
Please note: general indications when preparing all
milk-based beverages
• “
ESC”: press to interrupt preparation completely and
go back to the homepage.
• "STOP ": press to interrupt milk or coffee delivery and
move on to the next delivery (if applicable) to complete the
beverage.
• At the end of delivery, to increase the quantity of milk or
coffee in the cup, press EXTRA ".
• Preparation of each coffee can be customised (see sections
“13. Customising the beverages” and”14. Memorising your
personal profile”).
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
Once the coffee has been made, the appliance is ready to make
the next beverage.
10.4 Cleaning the milk container after use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout (D5).
Avoid contact with splashes of water.
