Dell XPS 8930 Service Manual Download Page 124

Page: 124 / 142

Table 5. System setup options—Advanced menu

Advanced

Advanced BIOS Features

Intel SpeedStep Technology

Allows you to enable or disable Intel
Speedstep Technology. Default: Enabled.

NOTE: If enabled, the processor
clock speed and core voltage are
adjusted dynamically based on the
processor load.

Virtualization

Allows you to enable or disable the Intel
Virtualization technology.
Default: Enabled

VT for Direct I/O

Allows you to enable or disable Intel
Virtualization Technology feature for the
Direct I/O.
Default: Enabled

SATA Operation

Allows you to configure the operating
mode of the integrated SATA hard drive
controller.

Intel Ready Mode Technology

Allows you to enable or disable the Intel
Ready Mode Technology.
Default: Enabled

Intel Software Guard Extensions

Allows you to enable or disable Intel
Software Guard Extensions.

BIOS Recovery from Hard Drive

Allows you to enable or disable BIOS
Recovery from hard drive.
Default: Enabled

BIOS Auto-Recovery

BIOS auto-recovery automatically
recovers BIOS without user actions.
Default: Disabled

Always Perform Integrity Check

Allows you to enable or disable Integrity
check.
Default: Disabled

USB Configuration

124

Summary of Contents for XPS 8930















































































































































Search results

Summary of Contents for XPS 8930

Reviews:

Related manuals for XPS 8930

Brands by name

Popular brands

Dell XPS 8930, Service Manual

Search results

Summary of Contents for XPS 8930

Reviews:

Related manuals for XPS 8930

Brands by name

Popular brands