Dell WORKSTATION M4600 Owner'S Manual Download Page 133

Page: 133 / 142

Option

Description
Default Setting: Touchpad/PS-2 Mouse

Numlock Enable

Allows you to enable the Numlock option
when the computer boots.
Default Setting: Enable Numlock

Fn Key Emulation

Allows you to set the option where the
<Scroll Lock> key is used to simulate the
<Fn> key feature.
Default Setting: Enable Fn Key Emulation

POST HotKeys

Allows you enable the sign-on screen
message display indicating the keystroke
sequence to access the System Setup
option menu.
Default Setting: Enable F12 Boot Option

Fastboot

Allows to set the option to speed up the
boot process. The options are:

•

Minimal

•

Thorough

•

Auto

Default Setting: Thorough

Virtualization Support
The following table describe the menu options of the Virtualization Support

menu.

Option

Description

Virtualization

Allows you to enable or disable the Intel
Virtualization Technology.
Default Setting: Enable Intel Virtualization

Technology

VT for Direct I/O

Allows you to enable or disable
Virtualization Technology for Direct I/O.
Default Setting: Disabled

Trusted Execution

This option specifies wether a Measured
Virtual Machine Monitor (MVMM) can

133

Summary of Contents for WORKSTATION M4600















































































































































Search results

Summary of Contents for WORKSTATION M4600

Reviews:

Related manuals for WORKSTATION M4600

Brands by name

Popular brands

Dell WORKSTATION M4600, Owner'S Manual

Search results

Summary of Contents for WORKSTATION M4600

Reviews:

Related manuals for WORKSTATION M4600

Brands by name

Popular brands