Dell WORKSTATION M4600 Owner'S Manual Download Page 126

Page: 126 / 142

Option

Description

NOTE: SATA is configured to support
RAID mode.

USB Controller

Allows you to control the USB controller.
The options are:

•

Enable Boot Support

•

Enable External USB Port

Default Setting: Enable USB Controller and

Enable External USB Port

Miscellaneous Devices

Allows you to enable or disable the
following devices:

•

Internal Modem

•

Microphone

•

eSATA Ports

•

Hard Drive Free Fall Protection

•

Module Bay

•

ExpressCard

•

Camera

You can also enable or disable:

•

Media Card and 1394

•

Enable Media Card only

•

Disable Media Card and 1394

Default Setting: Media Card and 1394.

Keyboard illumination

Allows you to configure the keyboard
illumination feature. The options are:

•

Disabled

•

Level is 25%

•

Level is 50%

•

Level is 75%

•

Levels is 100%

Default Setting: Level is 25%

Drives

Allows you to configure the SATA drives
on board. The options are:

126

Summary of Contents for WORKSTATION M4600















































































































































Search results

Summary of Contents for WORKSTATION M4600

Reviews:

Related manuals for WORKSTATION M4600

Brands by name

Popular brands

Dell WORKSTATION M4600, Owner'S Manual

Search results

Summary of Contents for WORKSTATION M4600

Reviews:

Related manuals for WORKSTATION M4600

Brands by name

Popular brands