Dell Latitude 5430 Service Manual Download

Page: 119 / 139

Table 11. System setup options—System information menu (continued)

Overview

Processor L3 Cache

Displays the processor L3 Cache size.

Microcode Version

Displays the microcode version.

Intel Hyper-Threading Capable

Displays whether the processor is Hyper-Threading (HT) capable.

64-Bit Technology

Displays whether 64-bit technology is used.

Memory Information

Memory Installed

Displays the total system memory installed.

Memory Available

Displays the total system memory available.

Memory Speed

Displays the memory speed.

Memory Channel Mode

Displays single or dual channel mode.

Memory Technology

Displays the technology that is used for the memory.

DIMM_SLOT 1

Displays the memory installed in slot 1.

DIMM_SLOT 2

Displays the memory installed in slot 2.

Devices Information

Panel Type

Displays the Panel Type of the system.

Video Controller

Displays the video controller type of the system.

Video Memory

Displays the video memory information of the system.

Wi-Fi Device

Displays the wireless device information of the system.

Native Resolution

Displays the native resolution of the system.

Video BIOS Version

Displays the video BIOS version of the system.

Audio Controller

Displays the audio controller information of the system.

Bluetooth Device

Displays the Bluetooth device information of the system.

LOM MAC Address

Displays the LAN On Motherboard (LOM) MAC address of the system.

Pass Through MAC Address

Displays the pass through MAC address of the system.

Cellular Device

Displays the cellular device information of the system.

Table 12. System setup options—Boot Configuration menu

Boot Configuration

Boot Sequence

Boot mode

Displays the boot mode.

Boot Sequence

Displays the boot sequence.

Secure Digital (SD) Card Boot

Enable or disable the SD card read-only boot.

By default, the

Secure Digital (SD) Card Boot

option is not enabled.

Secure Boot

Enable Secure Boot

Enable or disable the secure boot feature.

By default, the option is not enabled.

Secure Boot Mode

Enable or disable to change the secure boot mode options.

By default, the

Deployed Mode

is enabled.

Expert Key Management

Enable Custom Mode

Enable or disable custom mode.

BIOS setup

119

Summary of Contents for Latitude 5430












































































































































Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands

Dell Latitude 5430, Service Manual

Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands