Dell INSPIRON Inspiron 5000 Service Manual Download Page 92 | Manualshive

Page: 92 / 100

background image

BIOS setup program

Entering BIOS setup program

Before turning on the Embedded Box PC, connect the keyboard, mouse, and monitor to the Embedded Box PC, or connect the
Embedded Box PC through the KVM session or use Dell Wyse Cloud Client Manager (CCM) or Dell Command | Monitor (DCM) to update
the BIOS configuration.

1. Turn on (or restart) the Embedded Box PC.
2. During POST, when the DELL logo is displayed, watch for the F2 prompt to appear, and then press F2 immediately.

NOTE:

The F2 prompt indicates that the keyboard is initialized. This prompt can appear very quickly, so you must

watch for it, and then press F2. If you press F2 before the F2 prompt, this keystroke is lost. If you wait too long and
the operating system logo appears, continue to wait until you see the desktop. Then, restart the Embedded Box PC
and try again.

Clearing forgotten passwords

NOTE:

The Embedded Box PC must be disconnected from the electrical outlet to clear the password setting.

1. Follow step 1 to step 6 in “

Removing the back cover

”.

2. Locate the password reset jumper (PWD) on the system board. See “

System-board components

”.

3. Move the jumper plug from pins 1 and 2 to 2 and 3.
4. Follow step 2 to step 9 in “

Replacing the back cover

”.

5. Turn on the Embedded Box PC, and wait until the message stating that the password has been cleared appears.
6. Shut down the Embedded Box PC.
7. Move the jumper plug from pins 2 and 3 and replace it on pins 1 and 2.

55

92

BIOS setup program

«
...
90
91
92
93
94
...
»

Summary of Contents for INSPIRON Inspiron 5000





































































































Reviews:

No comments

Related manuals for INSPIRON Inspiron 5000

Brand: Gateway Pages: 96

WMBX-3011-2701 series

Brand: WynMax Pages: 58

IntelliStation Z Pro Type 6866

Brand: IBM Pages: 194

6862 - PC 300 PL

Brand: IBM Pages: 208

Brand: UUGear Pages: 25

Brand: Acer Pages: 61

Brand: Acer Pages: 24

Brand: Acer Pages: 32

Brand: Acer Pages: 32

Brand: Acer Pages: 29

Aspire 7100 System

Brand: Acer Pages: 108

Brand: Acer Pages: 108

Brand: Acer Pages: 130

Altos G330 Series

Brand: Acer Pages: 134

Aspire 1820PT Series

Brand: Acer Pages: 216

Brand: Acer Pages: 114

Brand: Acer Pages: 130

Brand: Acer Pages: 121

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands