Dell INSPIRON Inspiron 5000 Service Manual Download Page 40

Page: 40 / 100

Removing the WLAN card

NOTE:

Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box

PC and follow the steps in

Before working inside your Embedded Box PC

. After working inside your Embedded Box PC,

follow the steps in

After working inside your Embedded Box PC

. For more safety best practices, see the Regulatory

Compliance home page at

www.dell.com/regulatory_compliance

Topics:

•

Prerequisites

•

Procedure

Prerequisites

1. Follow step 1 to step 6 in “

Removing the back cover

”.

2. Remove the

PCI/PCIe card

(if installed).

Procedure

1. Disconnect the antenna cables connected to the WLAN card.
2. Remove the screws that secure the WLAN-card bracket to the system board.
3. Remove the WLAN-card bracket from the WLAN card.
4. Slide and remove the WLAN card from the mPCIE2 slot.

1. WLAN-antenna cables (2)

2. WLAN-card bracket

3. M2x3 screws (2)

4. mPCIE2 slot

5. WLAN card

Removing the WLAN card

Summary of Contents for INSPIRON Inspiron 5000





































































































Search results

Summary of Contents for INSPIRON Inspiron 5000

Reviews:

Related manuals for INSPIRON Inspiron 5000

Brands by name

Popular brands

Dell INSPIRON Inspiron 5000, Service Manual

Search results

Summary of Contents for INSPIRON Inspiron 5000

Reviews:

Related manuals for INSPIRON Inspiron 5000

Brands by name

Popular brands