Dell Inspiron 7591 2-in-1 Service Manual Download Page 39 | Manualshive

Page: 39 / 80

background image

Replacing the touchpad

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

1. Slide the touchpad into the slot on the palm-rest assembly.
2. Replace the two screws (M1.6x2) that secure the touchpad to the palm-rest assembly.

Removing and installing components

39

«
...
37
38
39
40
41
...
»

Summary of Contents for Inspiron 7591 2-in-1

















































































Reviews:

No comments

Related manuals for Inspiron 7591 2-in-1

Brand: Acer Pages: 113

Aspire 4240 Series

Brand: Acer Pages: 13

Brand: Acer Pages: 106

Aspire 3000 Series

Brand: Acer Pages: 123

Brand: Acer Pages: 320

Aspire 1360 Series

Brand: Acer Pages: 104

Aspire 3810T Series

Brand: Acer Pages: 100

Brand: Acer Pages: 157

Aspire 3000 Series

Brand: Acer Pages: 84

Aspire 3000 Series

Brand: Acer Pages: 80

Brand: NEC Pages: 117

Brand: Samsung Pages: 143

Brand: Samsung Pages: 122

Brand: Prowise Pages: 22

Brand: Alienware Pages: 111

Brand: ASROCK Pages: 38

Brand: IBM Pages: 10

Intel PRO/100 SP

Brand: IBM Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands