Dell Inspiron 7591 2-in-1 Service Manual Download Page 25 | Manualshive

Page: 25 / 80

background image

Replacing the I/O board

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

1. Slide the I/O board into the slots on the palm-rest assembly.
2. Align the screw hole on the I/O board with the screw hole on the palm-rest assembly, and replace the screw (M2x3) that secures the

I/O board to the palm-rest assembly.

3. Close the right display hinge.
4. Replace the two screws (M2.5x4) that secure the right display hinge to the I/O board.
5. Connect the coin-cell battery cable to the I/O board.
6. Slide the fingerprint-reader cable into the connector on the I/O board and close the latch to secure the cable.
7. Connect the I/O-board cable to the I/O board.

Removing and installing components

25

«
...
23
24
25
26
27
...
»

Summary of Contents for Inspiron 7591 2-in-1

















































































Reviews:

No comments

Related manuals for Inspiron 7591 2-in-1

Brand: NEO Pages: 31

Brand: IBM Pages: 5

Brand: IBM Pages: 125

Joybook R41 series

Brand: BenQ Pages: 42

visionbook 14Wg Plus

Brand: UMAX Technologies Pages: 34

AMILO Xi Series

Brand: Fujitsu Siemens Computers Pages: 96

Atlas KAL14N300HA

Brand: Kogan Pages: 10

Brand: Acer Pages: 354

Brand: Acer Pages: 274

Brand: Acer Pages: 230

Inspiron 24 5410 All-in-One

Brand: Dell Pages: 27

Inspiron 17 7000 Series

Brand: Dell Pages: 2

Brand: Dell Pages: 77

Inspiron 16 Plus 7620

Brand: Dell Pages: 26

Inspiron 17 7000 Series

Brand: Dell Pages: 23

Brand: Dell Pages: 222

Brand: Dell Pages: 88

Inspiron 16 Plus 7620

Brand: Dell Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands