Dell Inspiron 7591 2-in-1 Service Manual Download Page 21 | Manualshive

Page: 21 / 80

background image

Post-requisites

Power-adapter port

Removing the power-adapter port

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Prerequisites

Remove the

Procedure

1. Remove the two screws (M2.5x4) that secure the left display hinge to the system board.
2. Lift the left display hinge from the system board.
3. Disconnect the power-adapter port cable from the system board.
4. Remove the screw (M2x3) that secures the power-adapter port to the palm-rest assembly.
5. Lift the power-adapter port, along with its cable, off the palm-rest assembly.

Removing and installing components

21

«
...
19
20
21
22
23
...
»

Summary of Contents for Inspiron 7591 2-in-1

















































































Reviews:

No comments

Related manuals for Inspiron 7591 2-in-1

Brand: Acer Pages: 14

Brand: Acer Pages: 14

Brand: Acer Pages: 15

ConceptD 3 Ezel

Brand: Acer Pages: 10

Brand: Acer Pages: 14

Brand: Acer Pages: 31

Chromebook Spin 13

Brand: Acer Pages: 36

Brand: Acer Pages: 13

Brand: Acer Pages: 73

Brand: Acer Pages: 10

Aspire 4930 Series

Brand: Acer Pages: 15

Brand: Acer Pages: 12

Aspire 4810 Series

Brand: Acer Pages: 38

Brand: Acer Pages: 112

Brand: Acer Pages: 150

Aspire 4730ZG Series

Brand: Acer Pages: 186

Brand: Acer Pages: 215

Aspire 4930 Series

Brand: Acer Pages: 222

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands