Dell Inspiron 7591 2-in-1 Service Manual Download Page 22 | Manualshive

Page: 22 / 80

background image

Replacing the power-adapter port

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

1. Place the power-adapter port into the slot on the palm-rest assembly.
2. Replace the screw (M2x3) that secures the power-adapter port to the palm-rest assembly.
3. Connect the power-adapter port cable to the system board.
4. Close the left display hinge.
5. Replace the two screws (M2.5x4) that secure the left display hinge to the system board.

22

Removing and installing components

«
...
20
21
22
23
24
...
»

Summary of Contents for Inspiron 7591 2-in-1

















































































Reviews:

No comments

Related manuals for Inspiron 7591 2-in-1

AcerNote Light 370P

Brand: Acer Pages: 16

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Satellite C855D

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands