Dell Alienware Aurora R8 Service Manual Download

Page: 82 / 113

Replacing the front-chassis fan

WARNING: Before working inside your computer, read the safety information that shipped with your computer and

follow the steps in

Before working inside your computer

. After working inside your computer, follow the instructions

After working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

Align the tabs on the front-chassis fan bracket with the front-chassis fan and press down on the fan until it snaps into

position.

2 Align the tabs on the front-chassis fan with the slots on the chassis and slide the fan until it snaps into position.
3 Connect the front-chassis fan cable to the system board.

Summary of Contents for Alienware Aurora R8


















































































































Search results

Summary of Contents for Alienware Aurora R8

Reviews:

Related manuals for Alienware Aurora R8

Brands by name

Popular brands

Dell Alienware Aurora R8, Service Manual

Search results

Summary of Contents for Alienware Aurora R8

Reviews:

Related manuals for Alienware Aurora R8

Brands by name

Popular brands