Dell Alienware 15 Service Manual Download

Page: 44 / 149

Removing the touch pad

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before working inside your computer

. After working inside your

computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory

Compliance home page at dell.com/regulatory_compliance.

Prerequisites

Remove the

base panel

Remove the

memory modules

Remove the

solid-state drives

Follow the procedure from step 1 to step 12 in “Removing the

palm rest

”.

Procedure

Lift the latches and disconnect the touch-pad cable and touch-pad

buttons cable from the touch pad.

Peel off the touch-pad cable from the touch pad.

Summary of Contents for Alienware 15






















































































































































Search results

Summary of Contents for Alienware 15

Reviews:

Related manuals for Alienware 15

Brands by name

Popular brands

Dell Alienware 15, Service Manual

Search results

Summary of Contents for Alienware 15

Reviews:

Related manuals for Alienware 15

Brands by name

Popular brands