Dell Alienware 15 Service Manual Download

Page: 141 / 149

Main

System Memory

Displays the system memory.

Extended Memory

Displays the extended memory.

Memory Speed

Displays the memory speed.

Advanced

Intel(R) SpeedStep (TM)

Allows you to disable or enable Intel (R)

SpeedStep Technology.
Default: Enabled

NOTE: If enabled, the processor

clock speed and core voltage are

adjusted dynamically based on the

processor load.

Virtualization

Allows you to disable or enable the

Intel Virtualization technology.
Default: Enabled

VT for Direct I/O

Allows you to disable or enable a

Virtual Machine Monitor (VMM) to use

the additional hardware capabilities

provided by Intel(R) Virtualization

Technology for Direct I/O.
Default: Enabled

Integrated NIC

Allows you to disable or enable the on-

board LAN controller.
Default: Enabled

USB Emulation

Allows you to enable or disable the

USB emulation feature. This feature

defines how the BIOS, in the absence

of a USB-aware operating system,

handles USB devices. USB emulation is

always enabled during POST.
Default: Enabled

NOTE: You cannot boot any type
of USB device (floppy, hard drive,

or memory key) when this option
is disabled.

USB PowerShare

Allows you to charge USB devices

when the computer is turned off or in

standby mode.

141

Summary of Contents for Alienware 15






















































































































































Search results

Summary of Contents for Alienware 15

Reviews:

Related manuals for Alienware 15

Brands by name

Popular brands

Dell Alienware 15, Service Manual

Search results

Summary of Contents for Alienware 15

Reviews:

Related manuals for Alienware 15

Brands by name

Popular brands