Dell Alienware 13 R3 Page 70 Service Manual Download

Page: 70 / 78

Replacing the display back-cover and antenna

assembly

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps
in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Topics:

•

Procedure

•

Post-requisites

Procedure

Place the display back-cover and antenna assembly on a clean and flat surface.

Post-requisites

1. Replace the

2. Replace the

3. Replace the

4. Replace the

5. Replace the

6. Replace the

7. Replace the

8. Replace the

9. Replace the

10. Replace the

11. Replace the

12. Replace the

13. Replace the

14. Replace the

15. Replace the

16. Replace the

Summary of Contents for Alienware 13 R3















































































Search results

Summary of Contents for Alienware 13 R3

Reviews:

Related manuals for Alienware 13 R3

Brands by name

Popular brands

Dell Alienware 13 R3, Service Manual

Search results

Summary of Contents for Alienware 13 R3

Reviews:

Related manuals for Alienware 13 R3

Brands by name

Popular brands