Dell Alienware 13 R3 Page 22 Service Manual Download

Page: 22 / 78

Replacing the rear-I/O cover

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps
in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Topics:

•

Procedure

•

Post-requisites

Procedure

1. Slide the rear-I/O cover into the slots on the computer base and snap the rear-I/O cover into place.
2. Replace the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Post-requisites

Replace the

base cover

Summary of Contents for Alienware 13 R3















































































Search results

Summary of Contents for Alienware 13 R3

Reviews:

Related manuals for Alienware 13 R3

Brands by name

Popular brands

Dell Alienware 13 R3, Service Manual

Search results

Summary of Contents for Alienware 13 R3

Reviews:

Related manuals for Alienware 13 R3

Brands by name

Popular brands