Dell Alienware 13 R3 Service Manual Download Page 67 | Manualshive

Page: 67 / 78

Dell Alienware 13 R3 Service Manual Download Page 67

Replacing the display hinges

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps
in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside your

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Topics:

•

•

Post-requisites

Procedure

1. Align the screw holes on the display hinges with the screw holes on the display back-cover and antenna assembly.
2. Replace the eight screws (M2.5x2.0L) that secure the display hinges to the display back-cover and antenna assembly.
3. Route the antenna cables through the routing guides on the display back-cover and antenna assembly.
4. Route the logo-board cable through the routing guides on the display back-cover and antenna assembly.
5. Route the display cable through the routing guides on the display back-cover and antenna assembly.
6. Place the hinge caps on the display hinges and press down to snap them into place.

Post-requisites

1. Replace the

.

2. Replace the

3. Replace the

display assembly

4. Replace the

5. Replace the

6. Replace the

heat-sink assembly

7. Replace the

coin-cell battery

8. Replace the

9. Replace the

10. Replace the

.

11. Replace the

solid-state drive

12. Replace the

13. Replace the

67

«
...
65
66
67
68
69
...
»

Summary of Contents for Alienware 13 R3















































































Reviews:

No comments