background image

Dell™ Latitude™ D610 Service Manual

 

 

 

 

Notes, Notices, and Cautions 

____________________ 

Information in this document is subject to change without notice. 

© 

2004

–2005 Dell Inc. All rights reserved.

 

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

 

Trademarks used in this text: 

Dell

, the 

DELL

 logo, and

 Latitude

 are trademarks of Dell

 

Inc.; 

Intel

 is a registered trademark of Intel Corporation; 

Bluetooth

 is a registered trademark 

owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license. 

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own. 

Model PP11L 

November 2005 Rev. A01

 

Before You Begin

Palm Rest

System Components

Fan

Internal Card With Bluetooth

® 

Wireless Technology

Microprocessor Thermal-Cooling Assembly

Hard Drive

Microprocessor Module

Center Control Cover

Speaker Assembly

Keyboard

Base Latch

Memory Module, Modem, and Devices

System Board

Coin-Cell Battery

Flashing the BIOS

Mini PCI Card

Pin Assignments for I/O Connectors

Display Assembly and Display Latch

 

NOTE: 

A NOTE indicates important information that helps you make better use of your computer. 

NOTICE: 

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. 

 

CAUTION: 

A CAUTION indicates a potential for property damage, personal injury, or death. 

Summary of Contents for 610D
















































Reviews: