Dell EMC ES40 Field Replacement Unit Manual Download Page 46 | Manualshive

Page: 46 / 66

background image

Figure 37 Installing the controller

CL4573

Transferring disks and disk filler modules

Starting with the disk or disk filler module in slot 0, transfer disks and any disk filler modules one at
a time from the faulted enclosure to the replacement enclosure.

NOTICE

Make sure to transfer the disks and any disk filler modules to the same slots in the

replacement enclosure that they occupied in the faulted enclosure. Installing disks out of their
original order results in data unavailability, and possible data loss.

Removing a disk

About this task

on page 47 while performing the procedure that follows.

Procedure

1. Pull the latch on the disk up.

2. Slowly pull the disks from its slot.

3. Place the disk on a static-free surface.

Removing and replacing FRUs

46

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

«
...
44
45
46
47
48
...
»

Summary of Contents for ES40



































































Reviews:

No comments

Related manuals for ES40

Brand: Safco Pages: 4

Brand: CAI Pages: 12

Brand: VAS Pages: 19

Brand: Yaasa Pages: 200

New Charterhouse 6028

Brand: Aspace Pages: 2

Brand: SAFAVIEH COUTURE Pages: 2

Chaise 88 5702 83

Brand: Homestyles Pages: 4

Brand: cinetto Pages: 28

Brand: Buffalo Tools Pages: 2

Brand: VonHaus Pages: 3

Brand: SAFAVIEH COUTURE Pages: 2

Brand: Vanico Maronyx Pages: 16

CHESTER FG0801380

Brand: Sonder Pages: 3

Metron Value 923544

Brand: Patterson Medical Pages: 4

Cellular Shades

Brand: Levolor Pages: 60

Brand: The Container Store Pages: 16

Sorelle PRIMO RTA 5760

Brand: C&T International Pages: 7

Brand: Happy Beds Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands