Dell EMC ES40 Field Replacement Unit Manual Download Page 21 | Manualshive

Page: 21 / 66

background image

Figure 6 Installing a power cooling module

CL5664

1

2

2. For an AC power cooling module:

a. Plug the power cord into the power cooling module.

b. Secure the power cord with the retention bail at the connector. The bail prevents the

power cord from pulling out of the connector.

Figure 7 Plugging in and securing the power cord

CL5765

2

1

3. For a DC power cooling module, push the power cord plug into the connector until it snaps

in place. The clips on the plug prevents the power cord from pulling out of the connector.

Verify the power supplies

Procedure

1. Enter the

enclosure show powersupply

command to find the status of all the power

modules.

# enclosure show powersupply

This command may take up to a minute to complete. Please wait...

Enclosure Description Status

--------- ------------------- -----

4 Power module A OK

4 Power module B OK

--------- -------------------- ------

Removing and replacing FRUs

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

21

«
...
19
20
21
22
23
...
»

Summary of Contents for ES40



































































Reviews:

No comments

Related manuals for ES40

Brand: Oemtools Pages: 8

Brand: OLG Pages: 8

Brand: ofinto Pages: 37

Brand: Unfinished Furniture of Wilmington Pages: 5

Brand: U-Line Pages: 6

Brand: WATSON Pages: 10

Brand: WATSON Pages: 17

Findley & Myers WD2442

Brand: CABINETS TO GO Pages: 4

Findley & Myers MBC30

Brand: CABINETS TO GO Pages: 5

Findley & Myers BC09

Brand: CABINETS TO GO Pages: 6

Brand: Galipette Pages: 12

Brand: Gami Pages: 3

Brand: VITRA Pages: 36

Brand: Ingersoll-Rand Pages: 1

Brand: Hanover Pages: 8

Brand: Balt Pages: 11

Brand: QABA Pages: 6

Brand: Astonica Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands