Dell EMC ES40 Field Replacement Unit Manual Download Page 35

Page: 35 / 66

Verify the operation of the new disk drive

Procedure

1. Rescan all of the disks by entering the

disk rescan

command

Note:

This command does not generate any output. The amount of time it takes to

complete depends on how many disks are attached.

2. After the rescan completes, enter the

disk show state

command to verify the state of

all drives. This command checks that the drive is recognized.

# disk show state

Enclosure Disk

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

--------- --------------------------------------------

1 . . . .

2 s R . . . . . . . . . . . . .

--------- --------------------------------------------

Legend State Count

------ ---------------------------- -----

. In Use Disks 17

s Spare Disks 1

R Rebuilding Disks 1

------ ---------------------------- -----

Total 19 disks

Note:

When the amber fault light has turned off on the front panel of the shelf, all the

disk are in good state.

3. After the rescan, if the output of the

disk show state

command displays any disks in

the

Unkown

Failed

, or

Absent

states, run the

disk unfail <enclosure-id>.<disk-

id>

command to unfail the disk. For example, to unfail enclosure 2, disk 2, type

disk

unfail 2.2

Installing and locking the front bezel

Before you begin

CAUTION

You must remove the protective plastic strip from the front of the bezel before

placing the system into operation. Failure to do this will cause the system to overheat.

About this task

Refer to

Figure 23

on page 36 while performing the procedure that follows.

Procedure

1. If present, remove the protective plastic strip from the front of the bezel.

2. Align the bezel with the enclosure.

3. Gently push the bezel into place until it latches.

4. Secure the bezel by turning the key in the lock.

Removing and replacing FRUs

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

Summary of Contents for ES40



































































Search results

Summary of Contents for ES40

Reviews:

Related manuals for ES40

Brands by name

Popular brands

Dell EMC ES40, Field Replacement Unit Manual

Search results

Summary of Contents for ES40

Reviews:

Related manuals for ES40

Brands by name

Popular brands