background image

Remote Management Unit: Dell PowerVault 124T DLT VS160 Autoloader User's Guide

file:///T|/htdocs/stor-sys/124T/en/124tvs16/rmu.html[12/5/2012 10:26:00 AM]

NOTE:

 Saved logs taken at point of failure are valuable for assessing problems. Service personnel may request

these logs.

Running Diagnostic Tests

A minimum of 2 cartridges are requiredd to run the diagnostic tests. The diagnostic tests available on the autoloader include:

Loader – Picker Test

Loader – Magazine Test

Loader – Inventory Test

Random Moves

1.  From any page, click the 

Error Log and Diagnostics

 heading. The 

Error Log and Diagnostics

 screen will be

displayed.

2.  In the 

Diagnostics

 section, select the diagnostic test that you want to run from the 

Test

 drop-down menu.

3.  Specify a loop count, if desired. Valid numbers are 1 to 99.

4.  Click 

submit

.

5.  While the test is running, you can view the status of the test. From 

View Diagnostic Test Progress

, click 

View

Status

.

A separate screen indicates which test is running and the current status of the diagnostic test.

6.  To view diagnostic progress click 

View Status

 again.

Identification

You can use the 

Identification

 feature of the autoloader by requesting the LCD backlight to flash for a specified number of

seconds.This can be helpful in identifying the location of the autoloader in an equipment room.

1.  From any page, click the 

Error Log and Diagnostics

 heading. The 

Error Log and Diagnostics

 screen displays.

2.  Under 

Identification

, enter the number of seconds in the 

Time (secs)

 field.

3.  Click 

Identify

. The LCD backlight flashes on the autoloader for the specified number of seconds.

Performing an Autoloader Reset

You will use autoloader reset when making SCSI ID changes and magazine changes. An autoloader reset will take at least

three minutes if there is a tape in the drive, or approximately 30 seconds otherwise. To perform an autoloader reset:

1.  From any page, click the 

Error Log and Diagnostics

 heading. The 

Error Log and Diagnostics

 screen displays.

2.  Under the 

Autoloader Reset

 section, click 

Autoloader Reset

.

Library Operations Page

You can move tapes, run a system inventory, reset the picker to its home position, or perform sequential operations from the

Library Operations

 page. When you click 

Library Operations

, the page displays.

Moving Tapes

Summary of Contents for PowerVault 124T DLT VS160
















































































Reviews: