background image

Remote Management Unit: Dell PowerVault 124T DLT VS160 Autoloader User's Guide

file:///T|/htdocs/stor-sys/124T/en/124tvs16/rmu.html[12/5/2012 10:26:00 AM]

Full Locking

 allows only one user to access the system and issue requests.

Time-based Locking

 allows only one user to access the system and issue requests with the lock expiring after

a designated amount of inactivity (in seconds).

Home/Logout

 is used to release a full or time-based lock and permit another user to access the system.

NOTE:

 Locking is only available to users on the authorized client list.

4.  Click 

submit

.

Firmware Page

NOTE:

 The preferred method of autoloader update is through the RMU (Remote Management Unit web interface). The

preferred method of drive update is across the host SCSI interface using the Dell Firmware Update utility (DFU) supplied

with the firmware update package. Refer to the README file provided with the firmware update package.

You can browse to find system updates and then upload the updates. To get system updates:

1.  From any page, click the 

Firmware

 heading. The 

Firmware Update

 screen displays.

2.  Click 

Browse

 to navigate to the host system for the update file. The file should end in an 

.img

 extension.

NOTE:

 It is recommended that all firmware updates be performed with image files located on the local system

hard drive as opposed to removable media devices or network share.

3.  Click 

Upload

.

4.  Click 

OK

 in response to the confirmation box. The autoloader automatically uploads the new code and processes it to

the system.

NOTE:

 A Microsoft issue may keep a user from updating drive or loader firmware over the RMU interface. This can

occur under Windows Server® 2003 with Service Pack 1 (SP1), or if a user has installed Microsoft Security Update

MS05-019. This problem displays as a 

6F Communication Error

 message on the front panel with the warning

light set. The RMU will continue to report the autoloader status as 

Initialization

.

For information and a workaround to this problem, go to 

Microsoft Technical Support Article 898060

. If this

problem occurs, the autoloader should be restarted to avoid further communication errors.

5.  Power cycle the loader, then the server after the firmware update is complete.

NOTE:

 After firmware update is complete, the unit will report new revision levels to the host on startup. You may have

to reconfigure your host backup software to recognize the updated unit.

Error Logs and Diagnostics Page

From the 

Error Log and Diagnostics

 page, you can run various tests on the autoloader. You can also view error and history

logs, test progress, identify the physical unit in a rack, or reset the system.

Viewing Error or History Logs:

1.  From any page, click the 

Diagnostics

 heading. The 

Diagnostics

 screen will be displayed.

2.  Under 

View Error and History Logs

, click 

View Logs

. You can also save the logs to a file by clicking 

Save Logs

. If

you save the logs to a file, you must select a destination folder within 60 seconds.

Summary of Contents for PowerVault 124T DLT VS160
















































































Reviews: