manualshive.com logo in svg

Deeplas OASIS POLYCARBONATE VERANDA, Installation Manual, Page: 28 / 36

Share
Download
Deeplas OASIS POLYCARBONATE VERANDA Installation Manual Download Page 28

2 8

  |   O A S I S   P O L Y C A R B O N A T E   V E R A N D A   I N S T A L L A T I O N   G U I D E

 

www.deponti.com 

Patio Roof Manual – Type Bosco 

 

31 

CLICK !

19

21

21

5. Repeat steps 1 to 4 on pages 29 & 30 for installation of the other cover strips.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6. Now screw a sheet stopper at the gutter end of each middle rafter to ensure secure attachment. 

Note: securing the end cover strips comes later. 

 

 

 

www.deponti.com 

Patio Roof Manual – Type Bosco 

 

31 

CLICK !

19

21

21

5. Repeat steps 1 to 4 on pages 29 & 30 for installation of the other cover strips.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6. Now screw a sheet stopper at the gutter end of each middle rafter to ensure secure attachment. 

Note: securing the end cover strips comes later. 

 

 

5. Repeat steps 1 to 4 on pages 26 & 27 for installation of the other cover strips.

6. Now screw a sheet stopper at the gutter end of each middle rafter to ensure secure attachment.
Note: securing the end cover strips comes later.

Summary of Contents for OASIS POLYCARBONATE VERANDA





































Reviews:

No comments