manualshive.com logo in svg

Deeplas OASIS POLYCARBONATE VERANDA, Installation Manual, Page: 27 / 36

Share
Download
Deeplas OASIS POLYCARBONATE VERANDA Installation Manual Download Page 27

2 6

  |   O A S I S   P O L Y C A R B O N A T E   V E R A N D A   I N S T A L L A T I O N   G U I D E

2 7

 

www.deponti.com 

Patio Roof Manual – Type Bosco 

 

30 

CLICK !

20

 

1. Place the second roofing sheet between the rafters. Note: UV side up, the long condensation 

profile with the tab down and on the gutter side. 

2. Carefully cut the pre-fitted rubber seals in the aluminium middle cover strip to size. 

3. Pre-drill the middle cover strip with a 3 mm drill bit (1 top – 1 bottom – 1 middle).  

Fit the middle cover strip. At the wall end the cover strip fits just a bit under the wall profile for extra 

anchoring. Once the strip is positioned correctly, click the trim click strip into the middle rafter (use a 

rubber mallet). 

4. Now screw the middle cover strip to three points on the middle rafter with long stainless steel 

screws (1 top – 1 bottom – 1 middle).  

 

 

1. Place the second roofing sheet between the rafters. Note: UV side up, the long condensation profile with the tab down and on 

the gutter side.
2. Carefully cut the pre-fitted rubber seals in the aluminium middle cover strip to size.
3. Pre-drill the middle cover strip with a 3mm drill bit (1 top – 1 bottom – 1 middle). Fit the middle cover strip. At the wall end the 

cover strip fits just a bit under the wall profile for extra anchoring. Once the strip is positioned correctly, click the trim click strip 

into the middle rafter (use a rubber mallet).
4. Now screw the middle cover strip to three points on the middle rafter with long stainless steel screws (1 top – 1 bottom – 1 middle).

Summary of Contents for OASIS POLYCARBONATE VERANDA





































Reviews:

No comments