manualshive.com logo in svg

Deep Sea Electronics Plc DSE5320, Operating Manual

Share
Download
Deep Sea Electronics Plc DSE5320 Operating Manual Download Page 66

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual 

66   

Part No. 057-014    5320 OPERATING MANUAL ISSUE 5.1    18/06/2007 ADM 

NEMA CLASSIFICATIONS

  

 

NOTE: - There is no direct equivalence between IP / NEMA ratings. IP figures shown are 

approximate only. 

 

1

 

IP30

 

Provides a degree of protection against contact with the enclosure equipment and against a limited amount of  falling dirt.

 

2

 

IP31

 

Provides a degree of protection against limited amounts of falling water and dirt.

 

3

 

IP64

 

Provides a degree of protection against windblown dust, rain and sleet; undamaged by the formation of ice on the enclosure.

 

3R

 

IP32

 

Provides a degree of protection against rain and sleet:; undamaged by the formation of ice on the enclosure.

 

4 (X)

 

IP66

 

Provides a degree of protection against splashing water, windblown dust and rain, hose directed water; undamaged by the 
formation of ice on the enclosure. (Resist corrosion).

 

12/12K

 

IP65

 

Provides a degree of protection against dust, falling dirt and dripping non corrosive liquids.

 

13

 

IP65

 

Provides a degree of protection against dust and spraying of water, oil and non corrosive coolants.

 

 
 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Summary of Contents for DSE5320



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands