manualshive.com logo in svg

Deep Sea Electronics Plc DSE5320, Operating Manual

Share
Download
Deep Sea Electronics Plc DSE5320 Operating Manual Download Page 15

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual 

 

Part No. 057-014    5320 OPERATING MANUAL ISSUE 5.1    18/06/2007 ADM   

15 

4.3  HIGH CURRENT WARNING ALARM 
 

GENERATOR HIGH CURRENT,

 if the module detects a generator output current in excess of the pre-set trip a 

warning is initiated. Alarm Warning High Current will be displayed. If this high current condition continues for an 
excess period of time, then the alarm is escalated to a shutdown condition. For further details of the high current 
alarm, please see High Current Shutdown Alarm. 
 

Alarm

 

Warning 

High current 

 
 

4.4 SHUTDOWNS 

Shutdowns are latching and stop the Generator. The alarm must be cleared, and the fault removed to reset the 
module. 
 

NOTE:- The alarm condition must be rectified before a reset will take place.  If the alarm condition 

remains it will not be possible to reset the unit (The exception to this is the Low Oil Pressure alarm and 

similar ‘delayed alarms’, as the oil pressure will be low with the engine at rest). 

 

FAIL TO START

, if the engine does not fire after the pre-set number of attempts has been made a shutdown will 

be initiated. Alarm Shutdown Fail To Start will be displayed. 
 

Alarm 

Shutdown 

Failed to start 

 

 
EMERGENCY STOP

, removal of the 

Positive DC

 Supply from the Emergency Stop input initiates the following 

sequence, firstly it will initiate a controlled shutdown of the Generator and prevent any attempt to restart the 
Generator until the Emergency Stop push-button has been reset. Secondly it removes the 

Positive DC

 supply from 

both the Fuel Solenoid and Starter Solenoid.  
 
Alarm Shutdown Emergency Stop will be displayed. 
 

Alarm 

Shutdown 

Emergency stop 

 
 

NOTE:- The Emergency Stop Positive signal must be present otherwise the unit will shutdown. 

 

LOW OIL PRESSURE

, if the module detects that the engine oil pressure has fallen below the low oil pressure trip 

setting level after the 

Safety On

 timer has expired, a shutdown will occur. Alarm Shutdown Low Oil Pressure will 

be displayed. 
 

Alarm 

Shutdown 

Low oil pressure 

 
 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Summary of Contents for DSE5320



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands