Deep Sea Electronics Plc DSE5320 Operating Manual Download Page 39

Page: 39 / 66

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual

Part No. 057-014 5320 OPERATING MANUAL ISSUE 5.1 18/06/2007 ADM

8.1.2 PLUG “B” 11 WAY

PIN

DESCRIPTION

CABLE

SIZE

NOTES

Charge fail / excite

2.5mm²

AWG 13

Do not connect to ground (battery –ve)

Auxiliary input 1

0.5mm²

AWG 20

Switch to Negative

Auxiliary input 2

0.5mm²

AWG 20

Switch to Negative

Auxiliary input 3

0.5mm²

AWG 20

Switch to Negative

Auxiliary input 4

0.5mm²

AWG 20

Switch to Negative

Auxiliary input 5

0.5mm²

AWG 20

Switch to Negative

Auxiliary input 6

0.5mm²

AWG 20

Switch to Negative

16 Functional

Earth

2.5mm²

AWG 13

Connect to a good clean earth point

Magnetic pickup Positive

0.5mm²

AWG 20

Connect to Magnetic Pickup device

Magnetic pickup Negative

0.5mm²

AWG 20

Connect to Magnetic Pickup device

19 Not

connected

NOTE:- Ensure magnetic pickup screen is connected to ground at one end only.

NOTE:- When the module is configured for CAN operation, terminals 17 & 18 should be left

unconnected. Engine speed is transmitted to the 53xx controller on the CAN link.

NOTE:- When the module is configured for CAN operation, FUEL, START and AUXILIARY output

requirements may be different. Refer to CAN and DSE Wiring for further information.

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Summary of Contents for DSE5320



































































Search results

Summary of Contents for DSE5320

Reviews:

Brands by name

Popular brands

Deep Sea Electronics Plc DSE5320, Operating Manual

Search results

Summary of Contents for DSE5320

Reviews:

Brands by name

Popular brands