manualshive.com logo in svg

Deep Sea Electronics Plc DSE5320, Operating Manual

Share
Download
Deep Sea Electronics Plc DSE5320 Operating Manual Download Page 61

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual 

 

Part No. 057-014    5320 OPERATING MANUAL ISSUE 5.1    18/06/2007 ADM   

61 

 
14.5 CAN INTERFACE 

 
Modules are fitted with the CAN interface as standard and are capable of receiving engine data from engine 
CAN controllers compliant with the CAN standard. 

CAN enabled engine controllers monitor the engines operating parameters such as engine speed, oil pressure, 
engine temperature (among others) in order to closely monitor and control the engine. The data that is gathered by 
the engine controller is then transmitted on an industry standard communications interface (CAN). This allows 
generator controllers such as the DSE 53xx range to access these engine parameters with no physical connection 
to the sensor device.  
 

NOTE:- For further details for connections to Can enabled engines refer to the manual Can and DSE 

Wiring    Part No. 057-004  

 
 

14.6 OUTPUT EXPANSION 

 
There are several methods of output expansion available for the 5xxx module:- 
 

14.6.1  RELAY OUTPUT EXPANSION (157) 

An expansion module is available, which connects to the configuration socket and enables the 5xxx to use eight 
additional relays on the 157 relay module, providing Volt-free contacts for customer connection.   A maximum of 2 
off 157 relay modules can be connected, there are identified as ‘A’ and ‘B’ and give a total of 16 extra relay 
outputs. 
 
Refer to technical data sheet on the 157 relay module for further details. 
 

14.6.2  LED OUTPUT EXPANSION (548) 

An expansion module is available, which connects to the configuration socket, and enables the 5xxx to use eight 
additional LED’s on the 548 module, providing remote LED’s indication up to 50 metres away.  A maximum of 2 off 
548 LED modules can be connected, there are identified as ‘A’ and ‘B’ and give a total of 16 extra LED outputs. 
 
It is possible to use a mix of 157 and 548 modules to give both relay and LED expansion if required (Please refer to 
our Technical Support department for details.). 
 

14.7 INPUT EXPANSION 

 
It is possible to increase the number of monitored inputs available by utilising either : 
 

¾

 

DSE P130 input expansion  

¾

 

54x Protection Expansion/Annunciator.   

 
Please refer to the relevant product documentation for further details. 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Summary of Contents for DSE5320



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands