background image

15

5. GUARANTEE

MANUFACTURER’S DECLARATION

The DeManincor firm guarantees the appliance has passed 

all the in-house tests and inspections and that is it therefore 

up to standard and without any manufacturing or material 

defects.

GENERAL TERMS

The guarantee is valid for 2 years from the date of purchase. 

It applies only to the original purchaser and is non-

transferable. The guarantee covers original manufacturing 

defects and applies to all of the product’s components.  

The warranty on the boiler only is extended to 5 years.
To request a service under the terms of the guarantee, the 

customer must present a valid proof of purchase (payment 

receipt, invoice, etc.). 

CONDITIONS

The request must be made through an authorized dealer. 
The DeManincor firm has the final say on what action should 

be taken to resolve any problems under the terms of the 

guarantee.
Any defective parts that are replaced remain the property of 

the DeManincor firm.
The DeManincor has the final say on whether the service 

under the terms of the guarantee should be done at the 

customer’s or its own premises.
For services offered under the guarantee, the customer is 

required to pay the minimum charges according to the going 

rates. This is not the case however if the cooker is purchased 

less than four months previously.
For repairs at DeManincor’s assistance centres, the customer 

is required to pay for the transport costs.

IMPERFECTION OR DEFECT IN THE MATERIALS

Imperfection or defect in the materials must be signalled 

within 8 days since the customer receives the products and 

anyway this implies only the obligation to replace what 

provided, excluding any additional responsibility.

COMPONENTS NOT COVERED BY THE GUARANTEE

The following are not covered:
• damage to parts attributable to negligence, carelessness or 

ineptitude, in particular deterioration to the heating plate 

caused by improper or lack of maintenance;

• damage to parts attributable to non-compliance with the 

instructions in this handbook;

• damage to parts attributable to transportation and failure 

to comply with some or all domestic and local regulations;

• damage to parts attributable to improper installation, 

insufficient capacity or faults with the electrical, hydraulic 

and gas connections, and inefficiency of the flues and 

discharge systems;

• the guarantee does not cover parts repaired by anyone not 

authorized by the DeManincor firm;

• technical services requested attributable to inefficiency of 

the flue and/or connecting pipes are not covered by the 

guarantee and charged according to the going rates;

• consumer parts like gaskets, glass, grids, refractory bricks, etc. 

SERVICES AFTER THE GUARANTEE

Any services after the period of the guarantee or which do 

not fall under the terms of the guarantee will be charged 

according to the going rates. In this case the cost of any 

replacements will also be charged.

RESPONSIBILITY

The DeManincor firm cannot accept any liability for any direct 

or indirect harm or damage to persons or objects caused by 

product defects if the rules set down by domestic or local law 

or by this handbook have not been complied with.

COMPETENT COURT

Disputes and litigations are always settled at the court  

of Trento.

PRODUCT MODIFICATIONS

The characteristics of the products described in the 

catalogues and this user and maintenance handbook are 

purely indicative. DeManincor aims to constantly improve 

upon its products and therefore reserves the right to make 

any changes and improvements it considers necessary 

without obligation for forewarning. DeManincor is also not 

obliged to apply previous or current changes to products 

already or in the progress of being constructed and assigned 

to customers.

4.3 STRUCTURE AND OTHER EXTERNAL PARTS

The stainless steel parts should be cleaned when cold with 

neutral detergents or with vinegar in the case of persistent 

stains. 

You must avoid using abrasive or acid products

 

that could damage the surface. Dry with a soft cloth, fol-

lowing the grain of the glazing.

The external parts can be cleaned easily with water and neu-

tral detergent. Do not use aggressive or abrasive chemical 

products; any spills from pans or other should be cleaned 

immediately.

english

Summary of Contents for EKB110





























Reviews: