background image

5

INSTALLATION INSTRUCTIONS FOR ECOMINERAL

INSTALLING THE POWER SUPPLY

Select a convenient well-ventilated location within one metre of filter equipment and mount the Power Supply 

vertically onto a post or wall 1.5 metres above ground level. Australian Standards requires that the Power 

Supply shall not be located within 3 meters of the pool water. Plug Power supply into a suitable weatherproof 

outlet and plug pump into the power outlet of the Power Supply Unit. The Unit must be kept away from acid 

and other chemical storage areas. Acid and chemical vapours will corrode the electronics inside the Unit.  

It must also be kept away from heat sources. Good ventilation is necessary for correct operation.

Return to pool line

Suction Line

PUMP

FILTER

ACCESSORIES

IN-LINE CELL

FLOW SWITCH

POWER SUPPLY

240V

Two self-tapping screws and wall plugs have been provided for fast and simple installation. 
Use a 6mm masonry drill bit when fitting Power Supply to a brick or concrete wall. When mounting to a post 

drill pilot holes and fit screws provided. Once screws are in position simply hang Sanitiser via bracket on 

back of Unit.

IMPORTANT: This diagram is intended to 

conform with SPASA for the safe operation of salt 

sanitisers. Any deviation is at the installer’s risk 

and may void the manufacturer’s warranty.

NOTE: The cell must be fitted to allow for easy 

removal and cleaning, and positioned after all 

accessories such as heater or pool cleaner, but 

before it divides if there is more than one return 

to pool line.

Summary of Contents for EMX3600





















Reviews: