Davco FUEL PRO 485 Technical Manual Download

Page: 9 / 21

FUEL PRO

485

TECHNICAL MANUAL

F1485 REV B

T e c h n o l o g y , L L C

DAVCO Technology, LLC

www.davco.com

800-328-2611

1600 Woodland Drive, Saline, MI 48176-1629

Pre-heater Wiring with Relay

30/51

12/24 VDC

OPTIONAL

RELAY

Heater

Pre-heater Fuse

Harness

Connector

Ignition
Circuit
Fuse

87A

30/51

The 12VDC or 24VDC electric pre-heater is installed in the

pre-heater port on the side of the Fuel Pro .

1 . Open the vent cap . Open the drain valve by turning one to

one and a half revolutions . Drain the Fuel Pro completely .

Close the drain valve .

2 . Remove the pipe plug in the heater port .
3 . Apply liquid thread sealant to the pre-heater threads and

install into the bottom plate . Tighten to 15-30 ft-lbs .

4 . Connect the chassis harness to the Fuel Pro harness .
5 . Connect the power lead to the fused accessory side of

the ignition switch . The fuse rating depends on the pre-

heater installed .

6 . Prime the Fuel Pro and check for leaks .

Approved fuse ratings

•

12VDC System:

20 amp fuse for a 155W PTC heater

25 amp fuse for a 195W PTC heater

•

24VDC System:

15 amp fuse for a 195W PTC heater

If the keyed circuit will not handle the required amperage for

the pre-heater, use a relay .

Pre-heater Port

12VDC/24VDC PRE-HEATER INSTALLATION

Summary of Contents for FUEL PRO 485






















Search results

Summary of Contents for FUEL PRO 485

Reviews:

Related manuals for FUEL PRO 485

Brands by name

Popular brands

Davco FUEL PRO 485, Technical Manual

Search results

Summary of Contents for FUEL PRO 485

Reviews:

Related manuals for FUEL PRO 485

Brands by name

Popular brands