background image

FUEL PRO

®

 485

TECHNICAL MANUAL

®

F1485 REV B

T e c h n o l o g y ,   L L C

17

DAVCO Technology, LLC

www.davco.com

800-328-2611

1600 Woodland Drive, Saline, MI  48176-1629

WARRANTY POLICY

Please review DAVCO’s Product Warranty terms and conditions carefully before installing and/or using a 

DAVCO product. 
Diesel Pro

®

 243 and 245, Fuel Pro

®

 382, 482, 483, 485, 487 and 488, Industrial Pro

®

, Pro-Chek

®

, Sea Pro

®

 

DAVCO Technology, LLC warrants these products to be free of defects in material and workmanship for five years, 500,000 miles 

or 10,000 hours (whichever comes first) and electrical parts for two-years, 200,000 miles or 4,000 hours (whichever comes first) 

from the purchase date* . 

Shop Pro

®

 

DAVCO Technology, LLC warrants the Shop Pro (except for the motor) to be free of defects in material and workmanship for two 

years from the date of purchase . The Shop Pro motor is warranted for one year from date of purchase .

REN Products, EyeMax

®

, and Fuel Pro

®

 384 

DAVCO Technology, LLC warrants these products to be free of defects in material and workmanship for two-years or 200,000 

miles (whichever comes first) from the purchase date .
By installing and/or using the product, you agree to be bound by the following: 

This Warranty does not apply to:

• 

Failure or inadequate performance due to improper installation, misuse, misapplication, faulty installation, alteration/

modification, poor maintenance, neglect, accident, or conditions resulting from actions outside DAVCO’s control, including 

but not limited to the use of contaminated, corrosive, and unapproved fluids .

• 

Downtime, loss of use, loss of profits or income, loss of capital, cost of substitute equipment, living expenses, claims by 

purchaser’s customers or other third parties, or other incidental, special or consequential damages .

• 

Attachments, accessory items, and parts not manufactured or distributed by DAVCO .

• 

Any aftermarket or OEM component not approved specifically to work with a DAVCO manufactured product

• 

Product that has been installed with aftermarket parts or altered or modified in any way .

• 

Normal wear and tear, abuse, vandalism, acts of God, improper storage or handling, disasters such as flood, fire, or war, 

failure to operate, maintain or repair in accordance with instructions, or failure to repair the vehicle into which the product is 

installed in accordance with the vehicle manufacturer’s instructions or common maintenance practices .

This warranty is the sole warranty made by DAVCO . DAVCO makes no other warranties, expressed or implied, of merchantability 

or fitness for a particular purpose .
In the unlikely event of a defective product, DAVCO will either rework the defective product or replace it at DAVCO’s discretion . 

If you feel you have a warrantable issue, contact DAVCO at 800-328-2611 for a Return Goods Authorization (RGA) number ** .  An 

RGA number is required prior to the return of any product .

* Purchase Date: The date of the first retail purchase of a new vehicle or piece of equipment from the OEM dealer or factory . For 

“Over the Counter” purchase: The date of sale to the first retail customer .
**Products submitted for Warranty consideration will be inspected by DAVCO personnel . Re-work or replacement will be based 

on DAVCO’s Warranty procedure and/or the results of their evaluation . DAVCO’s Warranty Program does not in any way consti-

tute a product guarantee .

Summary of Contents for FUEL PRO 485






















Reviews: