Datavideo TLM-170K Instruction Manual Download Page 11

Page: 11 / 52

Headphone Jack
Once the 3.5mm headphone jack is connected, the internal
speaker will be automatically muted.

Rear Panel

Ports

Descriptions

3.5mm Tally Light Input

Tally light input. The tip, ring and sleeve of the phone jack should
be connected to tally red, tally green and the ground.

Loop Thru Output

A loop thru output of SDI and HDMI inputs.

HDMI Input 1/2

Connect HDMI video and audio source devices.
HDMI 1: YUV420 not supported
HDMI 2: YUV420 supported

USB 2.0 Port (SERVICE)

For firmware upgrade only; see

Firmware Update

for more

information about firmware upgrade.

SDI Input / Output

1 SDI input/output pair

DC IN 12V

12 V power input (XLR/Phoenix Terminal)

Power ON/OFF Switch

TLM-170K’s main power ON/OFF switch

SDI Input / Output

HDMI Input 1 / 2

USB Port

DC IN 12V
(XLR)

3.5mm Tally light

input socket

ON/OFF Switch

Loop Thru Output

DC IN 12V
(Phoenix)

Summary of Contents for TLM-170K





















































Search results

Summary of Contents for TLM-170K

Reviews:

Related manuals for TLM-170K

Brands by name

Popular brands

Datavideo TLM-170K, Instruction Manual

Search results

Summary of Contents for TLM-170K

Reviews:

Related manuals for TLM-170K

Brands by name

Popular brands