background image

 

O v e r v i e w  

 

  

Introduction 

 

The M-Class M1 and M2 series of printers are available with several Communication Card options.  These cards can be 
equipped in the following configurations: 
 

ƒ

 

Wired and Wireless Ethernet and USB Host* 

ƒ

 Wired 

Ethernet 

ƒ

 

Wired and Wireless Ethernet 

ƒ

 USB 

Host* 

ƒ

 

Wired Ethernet and USB Host* 

 

* Not avialable on the M1 model. 

 

External Hardware Descriptions 

 

The functions of the Interface Card’s external hardware are defined below. Depending on the configuration 
of your card some items may not be present. 

 

Connectors 

ƒ

 

ANTENNA

 is used to connect an antenna or coaxial cable for RF reception and transmission via this Multimedia 

Communication Exchange (MMCX) Reverse Pin type connector. 

 

ƒ

 

10/100 BaseT

 is used to connect a 10/100 BaseT Ethernet cable via this RJ45 network connector.

 This port can not be used 

for the setup of the wireless portion of the card.

 

 

Indicator Lights 

ƒ

 

ACTIVITY 

is a green indicator that flashes when the Card is not connected and scanning. The indicator will turn on when a 

connection is made.

 

 

ƒ

 

LINK 

is a yellow indicator that comes on when the Card is associated with an Access Point or Ad-hoc peer.

 

 

ƒ

 

DATA 

is a green indicator that flashes when there is data transmitted between the printer and Host access point. 

 

USB Host Ports 

The USB Host Ports accept external memory storage devices for fonts, graphics, label formats, and firmware upgrades. Additionally, 
the USB Host Ports can accept a USB keyboard for direct data stand-alone input applications (e.g., Line Mode). 

 

Reset Button 

When pressed and held for five seconds, this causes the Card to reset to the factory default parameters. 

 

 

;

 Note:  

After using this Reset Button the printer must be reset using the front panel before the printer will be able to 
communicate with the card. Resetting the printer from the front panel will reset both the printer and the wireless card. 

 

Label 

This 

Label

 contains the MAC address of the Wireless Card.  The MAC address of the printer’s wired port is listed on the printer’s 

configuration test label.

 

ANT

ACTIVITY

LINK

DATA

RESET

WIRE

L

E

S

S

 
 

Installing the Antenna (wireless cards only) 

 

 

1.

 

Extend the 

Antenna

 then align the 

Base

 to the 

Connector

 

2.

 

Turn the 

Base

 clockwise until fully seated and tight on 

the 

Connector

.  

 

3.

 

Raise and position the 

Antenna. 

To avoid permenate damage, do not pull on the antenna when 
handling the Wireless Card 

Antenna

Connector

Base

 

 

Summary of Contents for M-Class Mark II M-4206





















Reviews: