Datalink Systems i50, Manual

Page: 70 / 75

i50 Manual (5.51) Page 70
© 2018 Datalink Systems, Inc. www.datalinksystemsinc.com
ID Name Description Default
108 I_GSPORTRX Globalstar UDP RX port
3616
109 I_GSPORTTX Globalstar UDP TX port
3615
110 I_BUFFER Buffer period for GPS reports. Range=0-64800 sec. 0=No Buffer
3600
111 I_GPRSPORTTX Cell UDP Port
4004
112 I_JREV OBD-II Max rev. Range=0-9999 rpm
6000
113 I_JBRK Not used
13
114 I_JACC Not used
8
115 I_JCOOL OBD-II Max coolant temp. Range=0-999 deg F
220
116 I_JTRANS Not used
240
117 I_JOIL Not used
240
118 I_JFUEL Not used
10
119 I_STARTTIME Time required to trigger start event. Range=0-64800 sec
10
120 I_GPRSCHECK Cell Keep Alive. Range=60-64800 sec. 64800=Never
0
121 I_BUFFEREVENTS
Select which data to buffer, when network buffering is enabled. 0=Positions
only. 1=Pos+Start/Stop. 2=Pos+All Events 0
122 I_JOILPRESS J1708 Min oil pressure. Range=0-99 PSI
5
123 I_HEADCHANGE Heading change reports. Range=0-90 degrees. 0=Off
0
124 I_HEADTIME Time required to trigger heading change event. Range=0-64800 sec
10
125 I_IDLELIMIT Max idle time allowed. Range=0-64800 sec. 0=No Limit
0
126 I_ENGINE1 Engine Hours (seconds)
0
127 I_ENGINE2 "
0
128 I_ODO1 Odometer (1/10 km)
0
129 I_ODO2 "
0
130 I_PERIODICWAKEUP Time between wakeup events while sleeping (sec)
0
131 I_MAXGPSWAIT Max time to wait for GPS signal during periodic wakeup (sec)
120
132 I_MAXSENDWAIT Max time to wait for network during periodic wakeup (sec)
120
133 I_IRIDIUMTIME Satellite time reporting limit in dual-mode. Range=0-64800 sec
0
134 I_IRIDIUMDIST Satellite distance reporting limit in dual-mode. Range=0-65500 metres
0
135 I_GPSUDPPORT
UDP port for sending GPS data during a dial-up or Wi-Fi connection. Set to
zero to disable. 2000
136 I_DYNIRIDIUM
Send Unit ID over Iridium to allow modems to be swapped between units
(1=Yes 0=No) 0
137 I_STATUS
Status report interval (Bits 7-6: Units 00=Days 01=Hours 10=Min. Bits 5-0:
Interval) 1
138 I_ALARMID Current Alarm ID used by MDS
0
139 I_FULLHEADING
Send full heading (0-360 degrees) instead of 8-point compass heading. Adds
one byte to each position packet (1=Yes 0=No) 0
140 I_COM1FLOW Turn flow control on for COM1 port (1=Yes 0=No)
0
141 I_COM2FLOW Turn flow control on for COM2 port (1=Yes 0=No)
0
142 I_COM1ROUTE COM1 route (0=COM1 1=RJ45 2=Wi-Fi)
0
143 I_SLEEPPIN
Pin used to trigger sleep mode. Bit 7=polarity. Bit 6=report at start-up. Bit
5=Motion wakeup. Bits 2-0=Input # (0=IGN, 1=Input 1, 2=Input 2, 3=Input 3,
4=Input 4) 0
144 I_ROUTERIP1 Router IP address assigned to i50 for dial-up or Wi-Fi access point sessions
192
145 I_ROUTERIP2 "
168
146 I_ROUTERIP3 "
0
147 I_ROUTERIP4 "
1
148 I_WIFICHANNEL Local Wi-Fi channel number (1-11)
6