DataDirect Networks StorageScaler 2460 Installation And User Manual Download Page 35

Page: 35 / 46

Technical Specifications

96-00290-001 Rev. A1

DataDirect Networks StorageScaler 2460 User Guide | 29

Here are the technical specifications for StorageScaler 2460.

NOTE :

Specifications subject to change without notice.

A.1

General Specifications

System

•

2U enclosure height (rack configurations)

•

Up to 24 2.5" SAS or SATA disk drives (including SSD’s) per enclosure (6 Gb/sec or
3 Gb/sec)

Redundant Components

•

Two APC units

•

Up to 24 drives per enclosure

Field Replaceable Units

•

Disk drives and drive carrier blanks

•

APC units

•

I/O modules

•

I/O module slot blanks

Enclosure Physical Dimensions

•

Height: 3.5" (89 mm)

•

Width: 17.6" (447 mm)

•

Depth: 19.3" (49 mm)

•

Weight: up to 53 lbs (27 kg) maximum (with all drives installed)

Advanced Power and Cooling (APC) Units

•

Input Voltage: 100–240 VAC

•

Current Rating: 8.40 A (max)

•

Input Frequency: 50/60 Hz

•

Outputs:

- +5 V @ 28 A

- +12 V @ 43 A

•

Maximum Average Output Power: 550 Watts

•

Cooling: Variable speed blowers, two per APC for a total of four blowers per enclosure

NOTE :

APC units are hot-swappable.

USO

RESTRITO

Summary of Contents for StorageScaler 2460















































Search results

Summary of Contents for StorageScaler 2460

Reviews:

Related manuals for StorageScaler 2460

Brands by name

Popular brands

DataDirect Networks StorageScaler 2460, Installation And User Manual

Search results

Summary of Contents for StorageScaler 2460

Reviews:

Related manuals for StorageScaler 2460

Brands by name

Popular brands