manualshive.com logo in svg

DataDirect Networks StorageScaler 2460, Installation And User Manual

Share
Download
DataDirect Networks StorageScaler 2460 Installation And User Manual Download Page 20

Installation

96-00290-001 Rev. A1 

DataDirect Networks StorageScaler 2460 User Guide  | 14

2.4

Installing the Disk Drives

CAUTION !

Acclimate new disk drives to room temperature before you install them. 
Store drives at room temperature for two hours prior to use. 

NOTE :

Combining SAS and SATA disk drives in this enclosure is not supported at 
this time. Please use either SAS or SATA disk drives, but not both.  

To install a disk drive: 

1.

Press the release button to release the lever on the carrier. 

2.

Hold the disk drive so that the LEDs are on the bottom and the lever is fully open.

3.

Slide the disk drive into the drive slot until the lever starts to close 

(Figure 18)

. 

Figure 18.  Disk Drive Inserted in Drive Slot 

4.

Gently push the lever until it mates with the latch on the bottom of the drive slot and 
clicks into place 

(Figure 19)

.

Figure 19.  Lever Latched 

NOTE :

To maintain proper airflow and cooling, a disk drive or a blank drive carrier 
must be installed in every slot of the enclosure.

USO 

RESTRITO

Summary of Contents for StorageScaler 2460















































Reviews:

No comments

Brands by name

Popular brands

Load more brands