manualshive.com logo in svg

Datacom Systems VS-1012-F, Fast Start Manual

Share
Download
Datacom Systems VS-1012-F Fast Start Manual Download Page 8

© 2015 Datacom Systems Inc

 

 

8 

VS-10XX-F, VS-11XX-F, VS-12XX-F FASTstart Guide

 

 

 

 

 

2.5  Front 

— Power & Status Indicators 

 

On the front panel, the power status of the device can be determined through three indicators labeled 
“POWER 1”, “POWER 2”, and “STATUS”.  

 

 

12-Port Versions 

 
 

 

24-Port Versions 

 

The LEDs located next to each power label will illuminate 

green 

when a power supply is 

connected and switched ON. 
 

When the power indicators illuminate 

red

, it indicates that there either is not a power supply 

connected, or it is not switched ON. 
 
Although only one power source is required to power the VERSAstream, use of a second 
independent power source is strongly recommended to assure uninterrupted monitoring. 

 

The “STATUS” LED indicator is 

orange

 during the boot-up cycle and turns 

green

 upon a 

successful boot sequence indicating the VERSAstream is operational. 
 

NOTE

: The “STATUS” LED indicator indicates the device is ready several seconds before it is 

ready to respond to Command Line Interface (CLI) commands. 
 

2.6  Front 

— Display and Buttons 

 

The display shows Serial and Management Port status. The Selectable Buttons are for future 
use. 

 

 

12-Port Versions Only 

 

Summary of Contents for VS-1012-F




























Reviews:

No comments

Brands by name

Popular brands

Load more brands