DataApex Agilent 7890 Manual Download Page 35

Page: 35 / 39

4 Using the control module

Clarity Controls

4.8.4 Sampler tab

Fig 20: Agilent 7890 Setup - Sampler

This

tab

displays

the

settings

of the

automatic

liquid

sampler

(autosampler) connected directly to GC. Settings on this tab may be read
from the chromatograph using the

Autodetect

button, however it is

advisable to verify them manually.

Use Sampler

Enables the autosampler for use with

Agilent 7890

chromatograph.

Needs to be unchecked if you want to start the acquisition from the

Clarity

Name

Allows to set the arbitrary name for the autosampler.

Type

Sets the type of the autosampler installed.

Front (Back) Injector

Enables the use of the particular injector.

Syringe Size

Sets the size of the syringe installed.

Solvent Wash Mode

Sets the solvent wash mode for the autosampler.

Tray

Sets the presence of an autosampler tray.

- 31 -

Summary of Contents for Agilent 7890








































Search results

Summary of Contents for Agilent 7890

Reviews:

Related manuals for Agilent 7890

Brands by name

Popular brands

DataApex Agilent 7890, Manual

Search results

Summary of Contents for Agilent 7890

Reviews:

Related manuals for Agilent 7890

Brands by name

Popular brands