DataApex Agilent 7890 Manual Download Page 24 | Manualshive

Page: 24 / 39

background image

Agilent 7890

4 Using the control module

4.3.6 PCM

Fig 12: Method Setup - GC - Inlet

This tab governs the settings concerning the Pressure Control Modules
installed in the

Agilent 7890

chromatograph. According to configuration of

particular chromatograph, there can be several tabs, both with the similar
appearance.

Pneumatics

Turns on/off the pneumatic control of a particular channel.

Mode

Sets the working mode of PCM Channel A.

Pressure

Sets the initial pressure (available only in Pressure mode).

Total Flow

Sets the initial Flow (available only in Flow mode).

Postrun Pressure

Sets the postrun pressure (available only in Pressure mode).

Postrun Flow

Sets the postrun Flow (available only in Flow mode).

- 20 -

«
...
22
23
24
25
26
...
»

Summary of Contents for Agilent 7890








































Reviews:

No comments

Related manuals for Agilent 7890

Brand: Eaton Pages: 86

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Spartan-3A DSP FPGA Series

Brand: Xilinx Pages: 140

Brand: mikroElektronika Pages: 3

Brand: Window Master Pages: 7

Brand: Case IH Pages: 81

SmartStuff Series

Brand: TCP Pages: 2

Brand: ADLINK Technology Pages: 37

Samos Pro Compact SP-COP2

Brand: Wieland Pages: 36

Brand: HM-Funktechnik Pages: 20

Bilge Pump Control Panel

Brand: SPXFLOW Pages: 14

Brand: HBM Pages: 88

Brand: Haiwell Pages: 18

SC600 Marcopolo

Brand: Valeo Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands