DataApex Agilent 7890 Manual Download Page 29

Page: 29 / 39

4 Using the control module

Clarity Controls

4.5 Method Setup - Valves

Fig 15: Method Setup - Valves

Each valve allows to set its parameters on the appropriate tab. To switch
to another valve, use the

Select Valve

field in the upper left corner of the

Method Setup - Valves

dialog. Each type of valve has different parameters

available, thus the appearance of

Valves

panel depends on the type of

selected valve.

Initially On

Selects the initial state of the valve. Available for

Switch

and

Other

valves

only.

BCD Inverted

Available for

Multiposition

valves only.

Step Time [s]

Sets the Step Time. Available for

Multiposition

valves only.

Position

Sets the position. Available for

Multiposition

valves only.

Loop Volume [cm3]

Sets the Loop Volume. Available for

Gas Sampling

valves only.

Load Time [min]

Sets the Load Time. Available for

Gas Sampling

valves only.

Inject Time [min]

Sets the Inject Time. Available for

Gas Sampling

valves only.

- 25 -

Summary of Contents for Agilent 7890








































Search results

Summary of Contents for Agilent 7890

Reviews:

Related manuals for Agilent 7890

Brands by name

Popular brands

DataApex Agilent 7890, Manual

Search results

Summary of Contents for Agilent 7890

Reviews:

Related manuals for Agilent 7890

Brands by name

Popular brands