Data-Tronix DT-HDIPUS User Manual & Installation Manual Download Page 7

Page: 7 / 30

NACE: 610-429-1511 | [email protected] | www.datatronix.biz | DT-HDIPUS Manual v1.0

Page 7

Front-Panel

Buttons/LEDs

Description

Reboot button

Reboots the device (unsaved settings will be lost)

RST / UPG

button

To reset all the settings of the device to factory

default:

1. 1.Press and hold the RST/UPG button and then

connect power to the device while pressing in the

RST/UPG button.

2. 2.Hold the button until CFG led to flashes 10 times

(about 10 seconds)

3. 3.After the CFG led stops flashing -release the

button

To upgrade firmware using the USB port:

1. 1.Plug-in the USB drive with the upgraded firmware

image (“hdip_upg.img”)

2. 2.Press and hold the RST/UPG button and boot-up

the device

3. 3.USB led will flash while copying the image from

USB drive (about 3~5 seconds)

4. 4.Wait until the CFG led stop flashing

5. 5.Release the RST/CFG button and wait for the

device to reboot and upgrade the firmware (about 1

minutes)

PWR

Power is ON

CFG

Indicates device is in configuration mode

USB

Indicates USB drive is mounted

MPEG-2

Indicates device is encoding video using MPEG-2

H.264

Indicates device is encoding video using H.264

MP2

Indicates device is encoding audio using MPEG-1 Layer 2

AAC

Indicates device is encoding audio using AAC

Dolby Digital

Indicates device is encoding audio using Dolby Digital

For

Recording IP

Summary of Contents for DT-HDIPUS































Search results

Summary of Contents for DT-HDIPUS

Reviews:

Related manuals for DT-HDIPUS

Brands by name

Popular brands

Data-Tronix DT-HDIPUS, User Manual & Installation Manual

Search results

Summary of Contents for DT-HDIPUS

Reviews:

Related manuals for DT-HDIPUS

Brands by name

Popular brands