background image

 

  

 

 

   

 

AS-8 

Ordercode: D1904 

Description of the device 

 

Features 

The AS-8 can be used for several purposes. Due to its intelligent design, the users can easily switch 
between a controllable audio mixer (with several inputs) and a signal splitter (with several controllable 
outputs). This makes the AS-8 a multifunctional solution for your own monitor mix, multi zone systems, 
conference applications and more. 
 

 

Power supply: 230V AC, 50Hz 

 

Power consumption: 15W 

 

Indicators: 6-digit LEDs -18/-12/-6/0/+12/clip 

 

Input impedance: 50 kOhm balanced, 25 kOhm unbalanced 

 

Input connectors: XLR and 1/4" TRS 

 

Max. input level: +21 dBu 

 

Output connectors: XLR and 1/4" TRS 

 

Output impedance: 60 Ohm balanced, 30 Ohm unbalanced 

 

Frequency response: 5 Hz – 40 kHz 

 

Controls: input levels, output levels, main link button, balance/pan control, ground lift 

 

SNR: >95 dBu 

 

THD: < 0,002% typ. @ +4 dBu, 1KHz 

 

Fuse: T3,15mAL/250V 

 

Dimensions:  

483 x 215 x 44 mm (LxWxH) 

 

19” x 1HE (LxH) 

 

Weight: 3 kg 

 

Frontside 

 

 

Fig. 01 

 

 

Main Input Level control 

Turn the control to set the main input gain, before the signal reaches the input bus. While in Splitter 
mode, turn the control to set the common output level for all mono outputs. The LED indicators 
above the control, display the input level of the main input, between -18 and +12 dB. 

 

Main Link button 

Depress the button to route the main input signal to the main out. It is possible to route up to 8 input 
channels to the main mix.

 

 

Main Output Level control 

Turn the control to set the output level applied to the main outputs. The levels at the 6 mono outputs 
remain unaffected. The LED indicators above the control, display the output level of the main input, 
between -18 and +12 dB. 

 

IN/OUT Level control (CH1-6) 

Turn the control to set the signal level of the individual channels. In Splitter mode, turn the control to 
set the output level of the mono channels. In Mixer mode, turn the control to set the amount of the 
mono channel’s input signal feeding into the main output section. The LED indicators above the 
control display the output level of the given channel, between -18 and +12 dB. 

 

Splitter/Mixer button (CH1-6) 

Press/depress the button to toggle between Splitter and Mixer modes. 

 

 

Summary of Contents for AS-8

















Reviews: