background image

 

  

 

 

13 

   

 

AS-8 

Ordercode: D1904 

Replacing the Fuse 

Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the 
fuse burns out, the product will not function whatsoever. If this happens, follow the directions below. 
01)

 

Unplug the unit from electric power source. 

02)

 

Insert a screwdriver into the slot in the fuse cover. Gently pry up the fuse cover. The fuse will come 
out. 

03)

 

Remove the used fuse. If brown or unclear, it is burned out. 

04)

 

Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover. Be sure to 
use a fuse of the same type and specification. See the product specification label for details. 

 
 

Troubleshooting 

DAP Audio AS-8 
This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps 
below in sequence until a solution is found. Once the unit operates properly, do not carry out following 
steps. 
01)

 

If the device does not operate properly, unplug the device. 

02)

 

Check power from the wall, all cables, connections, etc. 

03)

 

The fuse. Replace the fuse. See page 13 for replacing the fuse. 

04)

 

If all of the above appears to be O.K., plug the unit in again. 

05)

 

If nothing happens after 30 seconds, unplug the device. 

06)

 

Return the device to your DAP Audio dealer. 

 
 

Product Specifications 

 

 

Power supply: 230V AC, 50Hz 

 

Power consumption: 15W 

 

Indicators: 6-digit LEDs -18/-12/-6/0/+12/clip 

 

Input impedance: 50 kOhm balanced, 25 kOhm unbalanced 

 

Input connectors: XLR and 1/4" TRS 

 

Max. input level: +21 dBu 

 

Output connectors: XLR and 1/4" TRS 

 

Output impedance: 60 Ohm balanced, 30 Ohm unbalanced 

 

Frequency response: 5 Hz – 40 kHz 

 

Controls: input levels, output levels, main link button, balance/pan control, ground lift 

 

SNR: >95 dBu 

 

THD: < 0,002% typ. @ +4 dBu, 1KHz 

 

Fuse: T3,15mAL/250V 

 

Dimensions:   483 x 215 x 44 mm (LxWxH) 

 

19” x 1HE (LxH) 

 

Weight: 3 kg 

 

 

 
Design and product specifications are subject to change without prior notice. 
 

 

Website: 

www.Dap-audio.info

 

Email: 

[email protected]

 

 

Summary of Contents for AS-8

















Reviews: